For a fire NOC or clearance in Karnataka, applicants are usually asked for approved plans, a built-up area statement, fire fighting and detection drawings, ownership and identity documents, structural and electrical certificates, and for renewals the previous certificate and maintenance records. Add test certificates and photos for passive fire products, which are often missing.
Why a checklist matters
Fire NOC requirements in Karnataka are mostly about evidence. An application is reviewed against drawings and then against the building. Gaps in the file mean questions, a second visit or a delay to occupancy. This checklist groups the papers usually asked for, based on published application guides and the KSFES portal. It ends with the group most files forget. For where the NOC fits among a building's wider duties, see the Bengaluru fire safety compliance handbook.
Group 1: plans
- Approved site plan
- Floor plans for every level, including basements and terrace
- Elevation and section drawings
- Built-up area statement
Group 2: fire system drawings
- Hydrant and wet riser layout
- Sprinkler layout where required
- Fire detection and alarm layout
- Pump room and tank details
- Fire compartment drawings showing rated walls, floors and doors
Compartment drawings are the bridge between the fire strategy and the passive work on site. Our guide to fire compartmentation under NBC explains what they should show.
Group 3: identity and ownership
- Ownership proof for the property
- Applicant identity and address proof
- Authorisation for the consultant filing on your behalf
Group 4: certificates
- Structural stability certificate from the structural engineer
- Electrical compliance certificate
- Test and commissioning reports for fire pumps, sprinklers and alarms
- For renewals: the previous fire certificate and maintenance records
Source: the document list in the NoBrokerHood guide, set against KSFES portal services. Always check the current list on the portal for your building type.
Group 5: passive fire evidence, the usual gap
This is where files most often fall short. Active systems come with commissioning reports. Passive work, done months earlier by different trades, often comes with nothing. Gather:
| Item | Evidence to keep |
|---|---|
| Fire door sets | Test certificate for the door, frame and hardware as a set; labels on doors |
| Shaft closing | Product test evidence; photos of each floor before and after |
| Penetration seals | Test reports, for example to ASTM E814 or EN 1366-3; location photos |
| Intumescent coatings | Product data, required thickness, measured thickness records |
| Fire rated walls | System details and tested build-up |
Source: test standards as published by ASTM and CEN. Our guides to passive fire audit documentation and installation documentation show what a complete record looks like.
Why files come back
- Drawings that no longer match the building. A staircase widened, a shaft moved, an extra room on the terrace, none of it updated on paper.
- Commissioning reports older than the last change. The pump was tested before the new tower block was connected.
- Products without proof. A door labelled as fire rated, but no certificate for the frame or hardware it was tested with.
- Photos without places. Pictures of seals with no floor, shaft or grid reference, so nobody can tell which opening is which.
- Consultant working from an old set. Revisions issued to the contractor but never to the person filing.
Each of these is cheap to prevent and slow to fix after the inspector has noticed. A short weekly check of what changed on site, and whether the file reflects it, avoids most of them.
How to assemble the file
- Start the file at design, not at the end of construction.
- Ask every trade that touches a fire wall for its records as it goes.
- Photograph each passive seal with a location tag before ceilings close.
- Do a walk-through a few weeks before inspection and list gaps.
- Hand the complete set to your consultant before filing on the KSFES portal.
Where we fit
We do not file NOC applications. We are passive fire specialists from Hyderabad. We seal shafts and penetrations with tested systems, apply intumescent coatings, and give you a photographed record for Group 5. If the work is already done by others, a passive fire audit documents what is there and what is not. For the approval itself, start with our fire NOC guide for Bangalore.
Sources:
- Karnataka State Fire and Emergency Services, official portal
- NoBrokerHood, fire clearance certificate in Karnataka (document list)
- Bureau of Indian Standards, National Building Code of India 2016, Part 4
- ASTM E814, fire tests of penetration firestop systems
Fire rules and their dates change, so confirm the current position with KSFES or your fire consultant before you act. Last reviewed 10 November 2026 by the Simfy Firesys team.



